Free Sample: Cisco CCNP ROUTE Chapter 1 Exam Questions and Answers
Want to get more free samples of Cisco CCNP Route exam questions and answers?
Click Here: Free Sample: Cisco CCNP ROUTE Chapter 2 Exam Questions and Answers and Free Sample: Cisco CCNP ROUTE Chapter 3 Exam Questions and Answerscisco ccnp route exam cost
1.Which two major areas can be used when discussing the highlevel overview of a typical enterprise network? (Choose two)
A.Building distribution
B.Building access
C.Campus backbone
D.Enterprise edge
E.Enterprise campus
Right Answers：DC
2.Which of the following is used when choosing a dynamic routing protocol?
A.Knowledge level of a specific routing protocol
B.Scalability
C.Type of links supported
D.Cost of equipment
E.Vendor support
Right Answers：AB
Note: If you want to get 100% real and valid Cisco CCNP exam dumps, you can contact SPOTO to buy latest ones.
3.BGP is which type of protocol?
A.Advanced distance vector
B.Linkstate
C.Path vector
D.Distance vector
Right Answers：C
4.Which two factors can influence convergence time for a routing protocol? (Choose two.)
A.Fine tuning routing protocol timers
B.Type of link between routers
C.Configuring route summarization
D.Size of the routing table
Right Answers：AC
5.Scalability of a network includes which two factors? (Choose two.)
A.Number of routers
B.Ability to do auto summarization
C.Number of adjacent neighbors
D.Distance between routers
Right Answers：AC
Note: If you want to get 100% real and valid Cisco CCNP exam dumps, you can contact SPOTO to buy latest ones.
6.Which of the following traffic types is not supported by IPv6?
A.Broadcast
B.Multicast
C.Anycast
D.Unicast
Right Answers：A
7.What is the IPv6 multicast address used by EIGRP?
A.FF02::6
B.FF02::5
C.FF02::9
D.FF02::A
Right Answers：D
8.Which type of IPv6 address is used by routing protocols for communications only on the link?
A.Linklocal
B.Site local
C.Unique local
D.Multicast
Right Answers：A
9.Which type of ICMPv6 message is sent by a device to request information about the network such as the prefix, prefix length and default gateway?
A.Router Advertisement
B.Router Solicitation
C.Neighbor Solicitation
D.Neighbor Advertisement
Right Answers：B
Note: If you want to get 100% real and valid Cisco CCNP exam dumps, you can contact SPOTO to buy latest ones.
10.Which type of ICMPv6 message is sent by a device to inform another device of its IPv6 address and associated Ethernet address?
A.Neighbor Solicitation
B.Router Advertisement
C.Router Solicitation
D.Neighbor Advertisement
Right Answers：D
11.Which type of network allows access to multiple devices on the same network but does not provide broadcast capabilities?
A.Multiaccess
B.NBMA
C.Broadcast
D.Pointtopoint
Right Answers：B
12.Which type of subinterface provides connections similar to physical pointtopoint links and has no neighbor discovery issues?
A.Multipoint
B.Pointtomultipoint
C.All of the above
D.Pointtopoint
Right Answers：D
13.Which tunneling protocol was developed by Cisco to encapsulate a Layer 3 protocol inside a pointtopoint, tunneloverIP network?
A.MPLS
B.DMVPN
C.IPsec
D.GRE
Right Answers: D
Note: If you want to get 100% real and valid Cisco CCNP exam dumps, you can contact SPOTO to buy latest ones.
14.A Layer 3 MPLS VPN over GRE is an example of what type of VPN?
A.DMVPN
B.Hybrid VPN
C.MultiVPN
D.Combination VPN
Right Answers: B
15.What is the main benefit of a GRE tunnel in respect to routing protocols?
A.Supports IP multicast
B.Stateless
C.Strong security
D.Low overhead
Right Answers: A
16.What protocol is used by routers to determine the nexthop IP address in tunneling networks?
A.MPLS
B.Dynamic GRE
C.NHRP
D.Mgre
Right Answers: C
17.What framework of open standards that provides confidentiality, data integrity, authentication and antireplay protection?
A.VPN
B.PSK
C.IPsec
D.PAP
Right Answers: C
18.R1 has an adjacent RIPng neighbor R2. R1 has a LAN with no neighbors, 2001:DB8:ACAD:1::/64. R1 advertises this prefix to adjacent RIPng neighbor, R2. What metric does R2 display for 2001:DB8:ACAD:1::/64?
A.2 hops
B.1 hop
C.4 hops
D.3 hops
Right Answers: A
19.How is an interface enabled for RIPng?
A.Interfaces are automatically enabled for RIPng when the RIPng process is started
B.Using the router ripng name interface command
C.Using the ipv6 router rip name interface command
D.Using the network prefix/prefixlength router mode command
Right Answers: C
20.Router R1 has multiple routes in its routing table including RIPng routes, directly connected networks and a static default route. R2 receives a static default route from R1 but no other routers. This is because R1 uses which option at the end of ipv6 rip name default information interface command?
A.defaultonly
B.static
C.only
D.originate